ISO INTERNATIONAL STANDARD 10792-2 First edition 1995-07-15 Aerospace -- Airframe spherical plain bearings in corrosion-resisting steel with self-lubricating liner - Part 2: Inch series Aéronautique Rotules en acier résistant a la corrosion, a garniture autolubrifiante, utilisées dans la structure des aéronefs - Partie2:Sérieseninches ISO Reference number ISO 10792-2:1995(E) rwintk1nfl ISO10792-2:1995(E) Foreword ISO (the International Organization for Standardization) is a worldwide preparing International Standards is normally carried out through IsO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International a vote. ISO/TC 20, Aircraft and space vehicles, Subcommittee SC 15, Airframe bearings. ISO10792 consists of the following parts, under the general title Aerospace - Airframe spherical plain bearings in corrosion-resisting steel with self-lubricating liner : Part 1: Metric series — Part 2: Inch series - Part 3:Technical specification Annexe A of this part of ISO 10792 is for information only. ISO1995 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International OrganizationforStandardization Case postale56·CH-1211Geneve20·Switzerland Printed in Switzerland ii Eeqr{tkijvgfd("WPG."E1 INTERNATIONAL STANDARD ISO ISO 10792-2:1995(E) Aerospace Airframe spherical plain bearings in corrosion-resisting steel with self-lubricating liner - Part 2: Inch series 1 Scope the possibility of applying the most recent editions of the standards indicated below. Members of IEC anc This part of ISO 10792 specifies the characteristics of Iso maintain registers of currently valid International spherical plain bearings in corrosion-resisting steel Standards. with self-lubricating liner, narrow and wide series, for elevatedloads at ambienttemperature,forusein ISO 683-16:1976, Heat-treated steels, alloy steels and fixed or moving parts of the aircraft structure and free-cutting steels -- Part 16: Precipitation hardening control mechanisms at temperatures of -55 ° to stainlesssteels. +163°C. ISO 683-17:1976, Heat-treated steels, alloy steels and free-cutting steels - Part 17: Ball and roller bearing It is applicable to self-lubricating spherical plain steels. bearings (without rolling elements) consisting of an outer ring having a concave sphered sliding contact ISO 1132:1980. Rolling bearings Tolerances surface with self-lubricating liner and inner ring having Definitions. a matched convex sphered sliding contact surface. ISO 6811:1983, Spherical plain bearings — Vocabu- At the time that this part of Is0 10792 was lary. developed, airframe spherical plain bearings with ISO 8075:1985, Aerospace- Surface treatment of dimensions originallyspecifiedinImperial units were dominant in world application. For this part of hardenablestainlesssteelparts. Is0 10792, the dimensions of these bearings have IsO 10792-1:1995, Aerospace - Airframe spherical been converted into metric units with the original plain bearings in corrosion-resisting steel with self- characteristics given in annex A for information only. lubricating liner — Part 1: Metric series. For new appications, the use of the bearings Is0 10792-3:1995, Aerospace — Airframe spherical specified in ISO 10792-1 is recommended. plain bearingsincorrosion-resisting steel withself lubricating liner—Part 3: Techni