ISO INTERNATIONAL STANDARD 9386-1 First edition 2000-11-01 Power-operated lifting platforms for persons with impaired mobility - Rules for safety, dimensions and functional operation : Part 1: Vertical lifting platforms Plates-formes élévatrices motorisées pour personnes a mobilite reéduite - Regles de seécurite, dimensions et fonctionnement - Partie 1: Plates-formes a course verticale Reference number ISO 9386-1:2000(E) ISO @ ISO 2000 ISO 9386-1:2000(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event ISO 2000 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 . CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.ch Printed in Switzerland ISO 2000 -All rights reserved ted without license from IHS ISO 9386-1:2000(E) Contents Page Foreword.. Introduction. 1 Scope. 2 Normative references .. 3 Terms and definitions .2 General requirements for lifting platforms 4.1 Pattern of use.... 4.2 Protection against hazards... 4.3 General design ........... 4.4 Design guidelines particular to the installation... 4.5 Access for maintenance, repair and inspection.... 4.6 Fire resistance.................... 4.7 Rated speed. 4.8 Ratedload 4.9 General safety factor.. 4.10 Resistance to operating forces.... .8 4.11 Protection of equipment against harmful external influences.. 4.12 Suppression of radio and television interference.... 4.13 Guarding..... 5 Guide rails, mechanical stops and mechanical blocking device. 5.1 Guide rails ... .9 5.2 Mechanical stops and mechanical blocking device.... 6 Safety gear and overspeed governor . 6.1 General. .9 6.2 Control ..... 6.3 Release 10 6.4 Access for inspection . 6.5 Electrical checking .... 10 6.6 Overspeed governor.. 11 6.7 Rotation monitor unit . 6.8 Safety nut... 7 Driving units and drive systems .... 7.1 General requirements.... 7.2 Braking system.... 12 7.3 Emergency/manual operation .... 7.4 Additional requirements for rope suspension drive .... 7.5 Additional requirements for rack and pinion drive .... 7.6 Additional requirements for chain suspension drive . 14 7.7 Additional requirements for screw and nut drive.. 15 7.8 Additional requirements for guided rope and ball drive....... 16 7.9 Additionalrequirementsforworm-toothedsegmentdrive 7.10 Additional requirements for friction/traction drive .... 16 7.11 Additional requirements for guided chain drive..... 16 7.12 Additional requirements for guided chain drive with bearing rollers and bearing segments... 7.13 Additional requirements for scissor mechanism drive .... ..16 7.14 Additional requirements for hydraulic drive..... 17 8 Electrical installation and equipment . .20 8.1 General...... ..20 ili icense from IHS