ISO INTERNATIONAL STANDARD 9445-1 First edition 2009-03-01 Continuously cold-rolled stainless steel Tolerances on dimensions and form - Part 1: Narrow strip and cut lengths Acierinoxydablelaminea froid en continu-Tolerances surles dimensionsetlaforme Partie 1:Bandes étroites etfeuillards coupesa longueur Reference number ISO 9445-1:2009(E) @ISO2009 ISO9445-1:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHTPROTECTEDDOCUMENT ISO2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, Iso's member body in the country of the requester. ISO copyright office Case postale 56 : CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland ISO 9445-1:2009(E) Contents Page Foreword iv 1 Scope 2 Normative references... 3 Terms and definitions.. 4 Informationtobesuppliedbythepurchaser 5 Type of delivery and delivery conditions. 6 Tolerances on thickness forcold-rolled narrow stripand products obtained from cold- rollednarrowstrip... 7 Tolerances on width for cold-rolled narrow strip and products obtained from cold-rolled narrow strip........ 8 Preferred coil inner diameters for cold-rolled narrow strip .. 9 Tolerances on length for cut lengths obtained from cold-rolled narrow strip. 10 Tolerances on edge camberfor cold-rolled narrow strip and cut lengths obtained from cold-rolled narrow strip.. 11 Tolerances on squareness for cut lengths obtained from cold-rolled narrow strip.. .5 12 Tolerances onflatnessforcutlengthsobtainedfromcold-rolled narrowstrip 13 Edgewavinesstolerancesforcold-rolled strip.... 14 Form of coils .. 15 Ordered format for cut lengths.... 16 Measurementofthicknessfor cold-rolled narrow stripandcut lengths obtained from cold-rolled narrow strip.... 9 17 Measurement of width.. 18 Measurement of length... 19 Measurement of edge camber. 20 Measurementofsquareness 21 Measurementofflatnessandwaviness. ISO9445-1:2009(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (Iso member bodies). The work of preparing International Standards is normally carried out through IsO non-governmental, in liaison with IsO, also take part in the work. iso collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2 adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO 9445-1 was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC 4, Heat treatable and alloysteels. This first edition of IsO 9445-1, together with IsO 9445-2, cancels and replaces ISO 9445:2002, the contents of whichhave been technically revised and separated into two parts. Iso 9445 consists of the following parts, unde