ISO INTERNATIONAL STANDARD 2017-1 First edition 2005-02-01 Mechanicalvibrationandshock- Resilient mounting systems Part 1: Technical information to be exchanged for the application of isolation systems Vibrationsetchocsmecaniques-Systemesdemontagerésilients Partie 1: Informations techniques a échanger pour I'application des systemesd'isolation Reference number ISO 2017-1:2005(E) @ISO2005 Copyright Intemational Organization for Standardization Not for Resale ISO 2017-1:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, ISO's member body in the country of the requester. ISO copyright office Case postale 56.CH-1211Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland Copyigh Intematilnal organization for Standardzation @ ISO 2005 - All rights reserved tted without license from IHS Not for Resale ISO2017-1:2005(E) Contents Page Foreword. iv Introduction 1 Scope. 2 Normativereferences 3 Termsand definitions. 4 Purposeofvibrationisolation (whyisolatemechanical systems). 5 What is to be isolated.... 5.1 Source isolation ... 5.2 Receiverisolation. 6 Applicability of vibration isolation (when to isolate structures or mechanical systems).. 7 Measurementand evaluation of vibration conditions.. 8 Information for the choice of an isolation mounting system ... 6 Informationtobesuppliedbytheproducerofthesourceorreceiver. 9.1 9.2 Informationtobesuppliedbythesourceproducer 9.3 Informationto be supplied bythe receiver producer.. 10 Informationtobesuppliedbythe customer. 10.1 Informationtobesuppliedbytheuserofthesource 10.2 Information to be supplied by the user of the receiver... 11 Informationtobeprovidedbythesupplieroftheisolationsystem 11.1 Physical data of the isolation system.... 11.2 Dynamic behaviour. 11.3 11.4 Environmental data... 11.5 Maintenance data. 10 12 Guidelines for the validation of isolation performance.. 10 AnnexA(informative)Elementsforvibrationisolation 11 Bibliography ili cense from IHS Not for Resale ISO2017-1:2005(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (isO member bodies). The work of preparing International Standards is normally carried out through IsO technical committees. Each member body interested in a subject for which a technical committee has been International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2. adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least75%of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO2017-1waspreparedbyTechnicalCommitteeISO/TC 108,Mechanicalvibrationand shock. This first edition of ISO 2017-1, together with ISO 2017-2, cancels and replaces ISO 2017:1982, which has been technically revised. ISO 2017 consists of the following parts, under the general title Mechanical vibration and shock- Resilient mounting systems: Part1:Technicalinformationtobeexchangedfortheapplicationofisolationsystems Part 2: Technical information to be excha