BS ISO 883:2013 BSl Standards Publication Licensed copy:IPLogin,Universityof Oxford,Versioncorrectasof Indexable hardmetal (carbide) inserts with rounded corners, without fixing hole - Dimensions bsi. ..making excellence a habit. BS ISO 883:2013 BRITISH STANDARD National foreword This British Standard is the UK implementation of IS0 883:2013. It supersedes BS 4193-2:1986 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee MTE/18, Tools tips and inserts for cutting applications. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. @The British Standards Institution 2013.Published by BSI Standards Limited 2013 ISBN9780580810206 ICS25.100.01 Compliance with a British Standard cannot confer immunityfrom legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committeeon30September 2013. Amendments issued since publication Date Textaffected BS ISO 883:2013 INTERNATIONAL ISO STANDARD 883 Fourth edition 2013-09-01 Indexable hardmetal (carbide) inserts with rounded corners, without fixing hole Dimensions Plaquettes amovibles enmetaux-durs (carburesmétalliques)avec arrondidepointe,sanstroudefixation-Dimensions Referencenumber IS0 883:2013(E) TSO @IS02013 BS ISO 883:2013 IS0883:2013(E) COPYRIGHTPROTECTEDDOCUMENT @IS02013 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form written permission. Permission can be requested from either ISO at the address below or ISo's member body in the country of the requester. ISO copyright office Case postale 56 : CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland i IsO2013-Allrightsreserved BS ISO 883:2013 IS0 883:2013(E) Contents Page Foreword ..iv 1 Scope. .1 2 Normativereferences ..1 3 Types of insert. 4 Interchangeability 4.1 Tolerances 4.2 Thickness, s, of inserts with chip breakers ..2 2 5 Designation and marking. 5.1 Designation .2 5.2 Marking .2 6 Measurement .2 7 Recommended dimensions ..2 7.1 General .2 3 7.2 Triangular inserts 7.3 Square inserts. 4 AnnexA (informative)Tolerancesford,mands .7 AnnexB(informative)Methodofmeasurementofm"dimension .8 Annex C (informative) Inserts with rounded corners without fixing hole, with shapes covered by thisInternational Standard 10 Annex D (informative) Relationship between designations in this International Standard and Is013399 (allparts) 12 Bibliography .13 IS0 2013 - All rights reserved ili BS ISO 883:2013 IS0 883:2013(E) Foreword Iso (the International Organization for Standardization) is a worldwide federation of national standards bodies (iso member bodies). The work of preparing International Standards is normally carried out through Iso technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with Iso, also take part in the work. Iso collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISo/IEc Directives, Part 1. In particular the different approval criteria needed for the different types of Iso documents should benoted.This document was drafted in accordancewiththe editorial rules oftheISO/IECDirectives, Part2.www.iso.org/directives Attention isdrawntothepossibilitythat some ofthe elements of this documentmaybethe subject of se patent rights.IsO shall not be held responsible for identifying any or all such patent rights. Details of anypatent